Відео

I watched this video it touched me so deeply. I showed my family, they were all touched as well. I then went to an open field set up a big screen and invited the whole town to watch. They all loved it so much we all held each other and cried with the satisfaction of such a great event. We are all now living better lives. Thank you so much for bringing this to our attention.

Will car run if I disconnect the wiring up there?

Sorry, but tools is everything. I've been doing bodywork for 33 years and I didn't start getting good at pushing till I got some good spline rods.

Amazing !

Thank u so much for the content

Commercial! You did not show us anything! hellooooooooooo like repairing the fender?

Awesome !!!!!

ive tried exactly the way your demonstrated on my 2020 accord and the dents won't pull out...

blud is acting like its a whole trade, aint that deep

What was the spray to release the tabs from the truck???

Yes, where can I get this! I’ve got a dent to pull!

I have a 2024 and backing of garage very small bump took it to ford they said we're the damage is they can't pop it the quarter panel has to be removed for new because the dent is in a un popping to a new quarter panel. They told me to change they have to take front end then the little side panel replaced with new . makes me sick$ 2.800

Having an instructor in person is always the best option. The instructor can gauge your progress and correct your mistakes in the beginning. Metal working and no joke. I didca glue pull on my dented fridge door🤣😂🤣 yeah more highs than lows. I didn't grasp to to move the metal wit a tap down tool. It takes tyme to understand how the metal memory works and how to manipulate it

Does the light matter when doing this?

I want to learn this pdr skill. A team was in my area for a week taking out dents. I had a small dent in my side door that i couldnt even tell where it was...to begin with i was sure the paint was chipped and cracked in.

I need this kit!!!

helo any videos on correcting errors and how to fix those errors?

Sold. If Jim (the dent tools freak) says it works, it's more than likely worth buying. 🫡

Hells fire I would put a pole in where every I was going to work - probably in a garage out of the weather oh yea 👍

Jesus H Criste dam it man -would have not believed it if I hadn’t seen it my self -frigin loved it - 5 stars to you an that puller ⭐️⭐️⭐️⭐️⭐️

Hey I hope you still look at comments on these. I’ve been trying to find the answer for an hour now. Can I use glue pullers if I have a paint chip on the dent?

At the finishing stage, how do we differentiate between those tiny lows and highs? How do we recognize them?

This is exactly what happened to my truck! I need this done, please share cuz folks are quoting me $2500 which is so sneaky when I see things like this online.

Where do I get one

This is what I call real craftsmanship 😎👌

Helo. Please let me know where your shop is.iam in los angeles ca. Yucaipa city.i want to get trained for pdr.are u local thanks in advance. 🙏

Is there any rule of thumb about what constitutes a dent that's too big for this method?

Good video 🤙🏻

That was amazing 👏 🎉

How much would a repair like the cost?

There are two types of people in this world: the fearful and the bold. With every failure the fearful confirms that they cannot do the job, the bold, on the other hand, are too busy learning how to be successful with every failure. Successful PDR work is based on trial and error. I always encourage people to boldly learn new things, your financial success lies in front of you! You can always find negative people to tear you down; look hard for supportive people who will provide you constructive criticism to accelerate your success.

What’s the cost comparison compared to getting a replacement part

i wonder if barcardis 151 would work as a glue release?????

Nice job. Would like to know where you got that kit. That’s all I need, my car has a smaller dent than the one on the video and I think I can get it fixed with a kit like that. Would appreciate your feedback. Thanks.

That mallet looks like a piece of a wheelbarrow handle.

Bro you should make tutorials just on video editing. 💯 on point

Cool job. Patience smarts responsibility to keep going 'til it's right. As long as enough people keep full coverage to pay for it. i've never paid out of pocket to beautify one of my hoopties. A good message for beginners would be to know something about kinesiology. Years of using knees and lower back wrong might be avoided. Better retirement years

Real good flick

how much do you charge to fix this fender?

The Best In the Business !!!

Hey brother I finished online with you, I think need in person now

What’s your thoughts on this tool 4 years later? Trying to decide between these and the cranes.

best video ever i laughed so hard but its true

I wish you were located in the Dallas area. There's no one I can trust around here to do mine properly.

My ram just got hit yesterday i will be trying this windshield replacement 1st.

I just started my PDR journey, it's humbling. The 20, 30 year guys just make it look like magic

Great work. Just curious,.how.much this repair would cost including paint? Ty